This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Extending DEADW input table with 2 extra columns
22-05-2012, 03:06 PM, (This post was last modified: 22-05-2012, 03:58 PM by shaswin.)
#1
Extending DEADW input table with 2 extra columns
When the W-LEVEL is set on YES and you have a discontinuty in your WALL table you can't use the IDENTifiers. You have to use AX-L, AX-LP, NODE or ELEM for the toggling state. This is not user-friendly when your configuration changes in the POLYDIF.

There is space in the DEADW input table for a DEADW-3 and DEADW-4 column:
DEADW-1 - deadweight pipeline part under water level left of the node (identifier);
DEADW-2 - deadweight pipeline part above water level left of the node (identifier);
DEADW-3 - deadweight pipeline part under water level right of the node (identifier);
DEADW-4 - deadweight pipeline part above water level right of the node (identifier);
W-LEVEL = YES

If W-LEVEL is empty or set on NO then DEADW-3 and DEADW4 should be empty:
DEADW-1 - deadweight pipeline part under or above water level left of the node (identifier);
DEADW-2 - deadweight pipeline part under or above water level right of the node (identifier);
W-LEVEL = NO or empty
Reply
30-05-2012, 03:30 PM,
#2
RE: Extending DEADW input table with 2 extra columns
You are correct, currently you can either use DEADW1 and DEADW2 to define a jump in deadweight, or use DEADW1 and DEADW1 to define the situation above and below water, but not both situations together.
We filed this request as ticket no. 1128.
Reply
29-07-2013, 03:26 PM, (This post was last modified: 29-07-2013, 03:27 PM by shaswin.)
#3
RE: Extending DEADW input table with 2 extra columns
Jens,

Can you give this wish more priority then my other wishes.
Is it possible to implement this in the next release?

Thanx
Reply
20-08-2013, 04:12 PM,
#4
RE: Extending DEADW input table with 2 extra columns
I will discuss it here, but there are quite a lot of underlying problems involved if we want to implement this request.

So no promises Confused
Reply
21-08-2013, 08:46 AM,
#5
RE: Extending DEADW input table with 2 extra columns
Another way is to allow duplicate IDENTIFIER names near each other to simulate the jump. The error shouldn't be displayed. The error should only be displayed when the IDENTIFIERS are not in increasing order.

This is then also backwards compatible with the older version of Ple4Win. The dimensions of the DEADW table would be the same.
Reply
13-09-2013, 03:31 PM,
#6
RE: Extending DEADW input table with 2 extra columns
You can always put two IDENTS close to each other in the POLYDIF table (or ADDIDENT) and approximate the jump by a very steep slope.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)